Sewer System

Pass-through sewer

The sewer system consists of:

1. PP feed pipes with diameters ranging from fi 160mm to fi 1000mm with nominal stiffness:

SN 8
SN 10

2. PP pass-through tubes without cup in the diameter range from fi 160mm to 1000mm with nominal stiffness:

SN 8

3. PE tubes; PP XXL in diameters from fi 1200mm to fi 2400mm with nominal stiffness:

SN 2
SN 4
SN 6
SN 8
SN 16

4. PP flow fittings in diameters ranging from fi 160mm to fi 1000mm

Monorelic Knee
Two-socket knee
Tee-piece
Tees with exit to smooth pipe
Sleeves
Reductions
Fittings
Fittings for chalks
< a href = "#s17"> Fittings for smooth pipes
Watertight passage through a concrete well
Universal Plug
External Cork
Inner Cork
Fifth Wheel connection with PP
Saddle 90 degrees
Hole Cutter
Seals

Purpose of the sewer system

The System of external drainage pipes and fittings made of PP polypropylene, in orange outside, and white in the middle, with structural walls is designed for the construction of a non-pressurized gravity sewer network ( Transport of sanitary, general and industrial wastewater). The pipes are produced in sections with working lengths of 3 or 6 meters. This System can be used as sewer wells and for laying wires and grombers under the drain. Polypropylene is particularly used for use in contaminated areas such as chemicals. Landfill and industrial waste, where the effluent from these wastes is very aggressive. The main advantage of the pass system is to use it for at least a period of 100 years. Another advantage is the use of a small amount of material for production, through which a small product weight is obtainedAnd despite all the high drainage rigidity. The high class of ring stiffness SN8 and SN10 allows the system to be used under heavy load conditions such as: domestic roads, highways and even airports. Both pipes and fittings can be combined with smooth pipes in any way, which is why they are used in individual applications. The pipes are produced by a coecking extrusion whereby two independent single-worm systems Plasticate polypropylene granules of two different colours but with similar properties, which is fed to the forming head Two pipes at the same time. The inner part of the tube is smooth, while the outer tube on the wall of the moulded sinuously (cored). The two layers of the pipe during production are combined with each other by means of pressure, creating a well-welded wall in the two-layer connection areas. Thanks to the construction of the exterior wall, they exhibit high stability when the local point loads occur, because the external wall takes over the load irregularities through its deformation. All types of PP and PE products are subjected to tests of mechanical strength, tightness and resistance to static and dynamic loads.

The network of sewage ducts with the use of penetrating Ground because of its lightness is considerably simplified. The pass-through System is 2-3 times lighter than plastic smooth-wall pipes.H solid, and 10-15 times lighter than stoneware or concrete pipes. The sewer System is resistant to the maximum temperature of wastewater up to + 60 degrees C at constant flow and + 95 degrees C; + 100 Degrees C for short-term flow.

PP Pass Pipes

PP (Polypropylene) pass-through pipes with a corrugated wall are produced in accordance with PN-EN 13476-3 with nominal peripheral stiffness SN 8 and SN 10. The pipes are manufactured in diameters ranging from fi 160mm to fi 1000mm in Orange at the outer (corrugated) wall and white in the middle of the tube. The exceptions are pipes from diameters fi 800mm to fi 1000mm, which have an external black color. The outer wall is a low-and wide-wave shape with narrow grooves, where a elastomer gasket is placed in the last groove to connect them. In addition, thanks to the exterior wall design, they exhibit high stability when local spot loads are present, because the external wall takes over its deformation of the load unevenness. Each tube, regardless of length, has a cup on one end and a second gasket. Strength calculations and technical considerations determine the applicability of different pipe types. The pass pipe System is also designed for the transport of industrial sewers, as shielding pipes for telecommunications and as drainage pipes for road drainage,and landfill. They are especially recommended for industrial sewers and in areas affected by mining damage due to their high impact resistance. It can be assumed that the noticeable fragility of the plastic occurs only at a temperature below-20 degrees C. At this temperature there are no contraindications in their transport or laying.

P-TubesPP (without Chalch)

Flow pipes made of PP (polypropylene) without a cup, with a corrugated wall are produced in accordance with PN-EN 13476-3 with a nominal drainage stiffness SN 8. The pipes are manufactured in diameters ranging from fi 160mm to fi 1000mm in Orange at the outer (corrugated) wall and white in the middle of the tube. The exceptions are pipes from diameters fi 800mm to fi 1000mm, which have an external black color. The pipes, thanks to the exterior wall design, show great stability in the presence of local point loads, because the outer wall takes over the deformation of the load unevenness. Strength calculations and technical considerations determine the applicability of different pipe types. Bosokoń's tubes (without chalices) as well as the tube tubes can also be combined, but using a two-socket coupling. The flow-free pipe System is also designed for the transport of industrial sewers, as shielding pipes for telecommunications and as drainage pipes for drainage of roads, landfills, landfill sites. Especiallyare recommended for industrial sewers and in areas affected by mining damage due to their high impact resistance. It can be assumed that the noticeable fragility of the plastic occurs only at a temperature below-20 degrees C. At this temperature there are no contraindications in their transport or laying.

Tube The EP Pass; PP XXL

XXL PP (Polypropylene) and PE (polyethylene) pass pipes with corrugated wall are produced in accordance with PN-EN 13476 + 3 + A1 with nominal peripheral stiffness SN 2, SN 4, SN 6, SN 8, SN 16. The pipes are manufactured in diameters ranging from fi 1200mm to fi 2400mm in black at the outer (corrugated) wall and white in the middle of the tube. The XXL System is mainly designed for the construction of sewage wells, reservoirs and pumping stations, but is also used for draining, draining and drainage systems. As with smaller diameters, the pass-through pipes are used for transporting industrial sewers as shielding pipes. In addition, pipelines in wastewater treatment plants, submarines (siphon systems, dump collectors), and trenchically refurbished methods. The main advantages of the system are their low weight compared to pipes with monolithic walls with similar static properties. The mounting method is as simple as that of smaller diameters due to the elastomeric gasket being assembled. Abrasion resistance is equalAn important distinguishing feature of PE pipes from other materials used in the construction of pipelines. Of the pipes of the XXL system with a variety of diameters are produced (under request) also fittings consisting of: arches, reducers, tees, whose angle of inclination is from 15 degrees C to 90 degrees C with the tips and length of the corresponding Segments. According to calculations and studies for changes occurring in natural conditions, it can already be predicted that the life of the sewage ducts of polyethylene and polypropylene laid in the ground should be at least 100 years.

PP Pass Fittings

< P>PP sewer fittings with corrugated wall (perforated) are manufactured in accordance with PN-EN 13476-3, in diameters ranging from fi 160mm to fi 1000mm, in Orange. The wide range of fittings offered allows to perform all kinds of connections occurring in sewage networks. The assortment includes: single-line knees, two-way knees, tees, tees with a departure to the smooth tube, sleeves, reducers, traditional fittings, for a cup, for smooth pipes, transitions sealed by concrete wells, stoppers, saddle connections, and seals. In terms of its performance and the possibilities of earthworks and assembly work related to the laying and joining by the use of suitable fittings in the ground, this constitutes an optimal drainage system allowing for StatementThat sanitary, industrial or universal sewer lines laid underground, under high load or in other areas, will be used for a period of at least 100 years and the investment costs will be optimal.

Advantages of the manufactured system:

Resistance to high temperatures-up to + 60 degrees C at constant flow and up to + 95 degrees C, + 100 degrees C with short-term flow
High wear resistance – abrasion resistance < Land >Chemical resistance to many chemical substances, resistance to urban wastewater with a commercial and economic origin ranging from acidity (pH2) to bases (pH12), rainwater and groundwater contaminated with waste Organic
Ysoka impact resistance-the fragility of the plastic occurs only at a temperature below-20 degrees C
The material flexibility module – much higher than the PE, causes the pipes to have high peripheral stiffness, both short and long-lasting
High Resistance to ageing in both natural and accelerated conditions – artificial
Excellent hydraulics – the smooth inner surface limits the deposition of contaminants.
Low weight in relation to stoneware, concrete and cast iron pipes, facilitating transport and accelerating installation
Total corrosion resistance – the destructive effects of groundwater, and thereforeThe system does not require the use of protective coatings
Guaranteed system durability over 100 years

Storage and Transportation

The pipes shall be transported in accordance with the applicable transport regulations. The pipe System in straight sections during transport should be arranged side-by-side on the entire surface, protected against sliding and damage. The free ends extending beyond the loading box shall not be longer than the limit values laid down in the regulations and shall be adequately protected and labelled. Particular attention shall be paid to the unloading of automotive supplies which should be duly carried out by appropriate equipment or by hand. During unloading as well as manual loading, appropriate OSH regulations should be maintained concerning the minimum weights of the transferred pipes by workers. Unloading the goods with a forklift can only be done with a trolley equipped with a smooth fork. It is permissible to store the pipes only on a substrate of equal, smooth and soft, preferably wooden, not causing damage. The period of storage of pipes depends on their production, but should not exceed a period of 12 months. The stored materials must also be protected against the effects of sunlight.

Assembly

at lowered ambient temperaturesTake special care when assembling pipes and fittings. Minimum temperatureSi-20 degrees C.
Do not damage or crack the mounted elements.
Check that the seal is installed correctly and that there is no damage to it.
The cleaned end of the tube with the gasket should be pressed in a smooth (inside) cup of another pipe or fittings. The dimensional System is designed so that joints with seals exhibit absolute tightness at a pressure of at least 0.5 bar or a vacuum pressure of 0.3 bar.
Auditing(a) The wires placed under the ground are controlled by CCTV cameras or video cameras, which should be carried out in order to correct the wiring – whether there are even cable drops or no outflow arregs .

< H2 andD = "T1" style = "text-align: center;" > Dimensions of PP pass pipe

SN 8
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)	Quantity in Package (PCS) palette
160	160	6000	35
160	160	3000	35
200	225	6000	15
200	225	3000	15
250	282	6000	12
250	282	3000	12
300	340	6000	9
300	340	3000	9
400	455	6000	3
400	455	3000	3
500	569	6000	2
500	569	3000	2
600	683	6000	2
600	683	3000	2
800	905	6000	2
800	905	3000	2
1000	1135	6000	2
1000	1135	3000	2

< TD Width = "25%" >300

SN 10
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)	Quantity in Package (PCS) palette
160	160	6000	35
160	160	3000	35
200	200	6000	15
200	200	3000	15
250	250	6000	12
250	250	3000	12
300	6000	9
300	300	3000	9
400	400	6000	3
400	400	3000	3
500	500	6000	2
500	500	3000	2
600	600	6000	2
600	600	3000	2
800	800	6000	2
800	800	3000	2
1000	1000	6000	2
1000	1000	3000	2

Dimensions of PP Pass pipe

(without Chalch)

< TD Width = "25%" >6000

SN 8
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)	Quantity in Package (PCS) palette
160	160	6000	-
200	225	15
250	282	6000	12
300	340	6000	9
400	455	6000	3
500	569	6000	2
600	683	6000	2
800	905	6000	2
100	1135	6000	2

SN 10
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)	Quantity in Package (PCS) palette
160	160	6000	-
200	225	6000	15
250	282	6000	12
300	340	6000	9
400	455	6000	3
500	569	6000	2
600	683	6000	2
800	905	6000	2
100	1135	6000	2

Dimensions of the XXL pass pipe

SN 2
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)
1600	1766	6000
1800	1966	6000
2000	2170	6000
2200	2372	6000
2400	2652	6000

SN 4
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)
1400	1566	6000
1600	1770	6000
1800	2052	6000
2000	2272	6000
2200	2480	6000
2400	2690	6000

SN 6
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)
1200	1366	6000
1400	1574	6000
1600	1852	6000
1800	2060	6000
2000	2280	6000
2200	2496	6000
2400	2726	6000

< P StyleE = "text-align: center;" >

SN 8
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)
1200	1370	6000
1400	1654	6000
1600	1860	6000
1800	2080	6000
2000	2292	6000
2200	2508	6000
2400	2726	6000

< tAble style = "margin-left: auto; margin-right: auto;" cellspacing = "0" cellpadding = "5" border = "1" width = "100%" >

SN 16

Inner diameter (mm)

Outer diameter (mm) garbs

Length (mm)

1200

1452

6000

1400

1680

6000

1600

1896

6000

1800

2126

6000

2000

2340

6000

2200

2550

6000

Dimensions of the pass fittings PP

< Table style = "margin-left: auto; margin-right: auto;" cellspacing = "0" cellpadding = "5" border = "1" width = "100%" >

Single-Hull PP knee

Diameter (mm)

Angle

1000

< TD atidth = "33%" >160

Two-socket knees PP
Diameter (mm)	Angle	Package Quantity (PCS)
160	90	70
45	80
160	30	80
160	15	100
200	90	48
200	45	64
200	30	64
200	15	64
250	90	27
250	45	32
250	30	32
250	15	32
300	90	24
300	45	27
300	30	27
300	15	27
400	90	8
400	45	8
400	30	8
400	15	8
500	90	4
500	45	4
500	30	4
500	15	4
600	90	2
600	45	3
600	30	3
600	15	3
800	90	-
800	45	-
800	30	-
800	15	-

Tees of cored pipes PP
Diameter (mm)	Angle
160/160	90
160/160	45
< P> 200/160	90
200/160	45
200/200	90
200/200	45
250/160	90
250/160	45
250/200	90
250/200	45
250/250	90
250/250	45
300/160	90
300/160	45
300/200	90
300/200	45
300/250	90
300/250	45
300/300	90
300/300	45
400/160	90
400/160	45
400/200	90
400/200	45
400/250	90
400/250	45
400/300	90
400/300	45
400/400	90
400/400	45
500/160	90
500/160	45
500/200	90
500/200	45
500/250	90
500/250	45
500/300	90
500/300	45
500/400	90
500/400	45
500/500	90
500/500	45
600/160	90
600/160	45
600/200	90
600/200	45
600/250	90
600/250	45
600/300	90
600/300	45
600/400	90
600/400	45
600/500	90
600/500	45
600/600	90
600/600	45
800/200	90
800/200	45
800/250	90
800/250	45
800/300	90
800/300	45
800/400	90
800/400	45
800/500	90
800/500	45
800/600	90
800/600	45
800/800	90
800/800	45
1000/200	90
1000/200	45
1000/250	90
1000/250	45
1000/300	90
1000/300	45
1000/400	90
1000/400	45
1000/500	90
1000/500	45
1000/600	90
1000/600	45
1000/800	90
1000/800	45
1000/1000	90
1000/1000	45

Tees of cored pipes PP To the smooth pipe
Diameter (mm)	Angle
160/160	90
160/160	45
200/160	90
200/160	45
200/200	90
200/200	45
250/160	90
250/160	45
250/200	90
250/200	45
250/250	90
250/250	45
300/160	90
300/160	45
300/200	90
300/200	45
300/250	90
300/250	45
300/315	90
300/315	45
400/160	90
400/160	45
400/200	90
400/200	45
400/250	90
400/250	45
400/315	90
400/315	45
400/400	90
400/400	45
500/160	90
500/160	45
500/200	90
500/200	45
500/250	90
500/250	45
500/315	90
500/315	45
500/400	90
500/400	45
500/500	90
500/500	45
600/160	90
600/160	45
600/200	90
600/200	45
600/250	90
600/250	45
600/315	90
600/315	45
600/400	90
600/400	45
600/500	90
600/500	45
800/200	90
800/200	45
800/250	90
800/250	45
800/315	90
800/315	45
800/400	90
800/400	45
800/500	90
800/500	45
1000/200	90
1000/200	45
1000/250	90
1000/250	45
1000/315	90
1000/315	45
1000/400	90
1000/400	45
1000/500	90
1000/500	45

Sleeves korugated PP
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)	Package Quantity (PCS)
160	182	167	150
200	254	220	140
250	317	270	72
300	376	315	45
400	499	427	24
500	615	437	20
600	731	508	12
800	970	657	2
1000	1212	817	2

Cored fittings PP
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)	Package Quantity (PCS)
160	182	167	150
200	254	220	140
250	317	270	72
300	376	315	45
400	499	427	24
500	615	437	20
600	731	508	12
800	970	657	2
1000	1212	817	2

Fittings to the Chalch (PVC or PP versions available)
Diameter of corrugated side (mm)	Solid side Diameter (mm)	Length (mm)
160	160	82
200	200	101
250	250	125
300	300	149
400	400	208
500	500	247
600	630	278

< TD Width = "33%" >400

Fittings For smooth pipe (PVC or PP versions available)
Diameter of corrugated side (mm)	Side diameter of a solid Chalch (mm)	Length (mm)
160	160	82
200	200	101
250	250	125
300	300	149
400	208
500	500	247

< TD Width = "50%" >415

Reduction of the PP cored tube
Diameter (mm)	Length (mm)
200/160	224
250/200	317
300/200	278
300/250	367
400/200	335
400/250	493
400/300	484
500/200	390
500/250
500/300	436
500/400	585
600/200	431
600/250	456
600/300	477
600/400	534
600/500	650
800/300	565
800/400	622
800/500	677
800/600	718
1000/300	654
1000/400	711
1000/500	766
1000/600	807
1000/800	895

Eccentric reductions PP Bk
Diameter (mm)	Length (mm)
200/160	224
250/200	314
300/200	298
300/250	387
400/200	362
400/250	440
400/300	511
500/300	461
500/400	610
600/300	498
600/400	555
600/500	671
800/400	665
800/500	720
800/600	761
1000/500	808
1000/600	849
1000/800	937

< TRvalign = "Top" >

250/200

251

Eccentric reductions PP BK/KG
Diameter (mm)	Length (mm)
200/160	212
250/160	234
300/200	295
300/250	321
400/200	359
400/315	407
500/200	412
500/315	460
600/200	449
600/315	497
600/400	522

< TDwidth = "50%" >160

Cored Tube stoppers PP Universal
Diameter (mm)	Length (mm)
161
200	197
250	239
300	283
400	372
500	480
600	535

Cored Tube stoppers PP (external)
Diameter (mm)	Length (mm)
800	397
1000	486

< ColgRoup >

Cored Tube stoppers PP (internal)
Diameter (mm)	Length (mm)
800	397
1000	486

Passage leak-proof PP (through concrete well)
Inner diameter (mm)	Outer diameter (mm) garbs	Length (mm)
160	182	91
200	254	110
250	317	131
300	376	154
400	499	209
500	615	268
600	731	309
800	970	395
1000	1212	480

Fifth Wheel Connection PP (mechanical connection)
Dimension (mm)
250-160
300-160
300-200
400-160
400-200
500-160
500-200
600-160
600-200
800-160
800-200
100-160
1000-200

Saddle 90 degrees C

(mechanical connection)

Dimension (mm)

250-200

300-200

400-200

500-200

< tD valign = "top" width = "100%" >Hole Cutter (For PP Fifth Wheel connection)

Dimension (mm)

160/177

200/214,5

Seals for PP cored pipe
Diameter (mm)
160
200
250
300
400
500
600
800
1000